X hits on this document

951 views

0 shares

0 downloads

0 comments

197 / 324

Section 8210.1 MASONITE Molded Panel Series Composite Particleboard Core Interior Doors

Part 1: GENERAL 1.1 Scope: Subject to local building codes, this product is intended for use in:

      • 1.1.1

        Single family dwelling interior applications.

      • 1.1.2

        Multifamily dwelling, low-rise professional office, library, and

low-rise motel interior applications. 1.1.3 Lighter use industrial building and factory, hotel, and retail sales building interior applications. 1.2 Product Description: 1-3/8" side-hinged door systems manufactured by MASONITE. 1.2.1 Door system components include: door panel(s), bifold panel(s), door frame, hinges.

Part 2: BASIC MATERIALS 2.1 Door Panel: Masonite 6 Panel Smooth Colonist Molded Panel doors shall be fabricated using loose lay up assembly that includes molded wood fiber facings, wood stiles, wood or MDF rails and particleboard core. Door facings are to be bonded to stiles, rails, and core forming a 3-ply structural attachment. Water based latex

primer used on door facings (stile and factory pre-finished. 2.1.1 Hinge preparations for 1-3/8" thick

accept

3-1/2"

hinges.

Face

bore(s)

rails per request) unless

doors to be machined to for cylindrical lock and

deadbolt are to be 2-1/8" diameter at 2-3/4" 2.1.2 Vertical edge of door to be square,

or 2-3/8"

backset.

beveled

both sides

or

lock stile only. Edge preparation should be clearly noted product is ordered. 2.2 Door Frame: Wood jambs shall be fabricated as a

when the

flat jamb

with doorstop applied.

Hinge jamb

doors to be preparations

machined to accept are to be machined for

preparations for 3-1/2" hinges. full lip cylindrical

1-3/8" thick Strike jamb strike plate.

Double door units at the top of door head jamb. 2.3 Hinges: (3) required on doors than TO".

shall include preparations for ball catch located on both door panels designed to strike into the

standard weight radius mortise hinges are TO" height or smaller & (4) on doors greater

Part 3: DELIVERY, STORAGE & HANDLING 3.1 Delivery: Reasonable care shall be exercised during shipping and handling in keeping with the decorative nature of product. 3.2 Storage & Protection: Store upright in a dry, well-ventilated

building or shelter at a damp, freshly plastered,

constant temperature.

Do not store in

drywall

or

concrete

areas

until

materials

have completely dried. Doors should be stored at least 10' from any heat source to help prevent uneven drying. Doors be sealed with an oil-based sealer or primer if stored for periods.

away must long

Part 4: EXECUTION 4.1 Examination: Site verification of substrate conditions, which have been previously completed, are acceptable for the product

installation specifications. instructions in accordance with Verify that door frame openings

plumb,

true and

level

before

beginning

installation

manufacturer's are constructed process. Select

fasteners of adequate type, intended functions. 4.2 Installation: Remove

number, and quality to perform the

protective packaging just prior to

installation. required and

Installer shall be experienced in performing work shall be specialized in the installation of work similar

to that required for this project.

Comply with

product data, including

product technical

bulletins,

installation instructions and product packaging installation. 4.3 Finishes: See Masonite - How to Paint

manufacturer's product catalog instructions for

instructions for

complete finishing details. Various types of materials are used the construction of the door system; each shall be sealed accordance with manufacturer's specifications to protect against

in in

various environmental conditions. Make sure to completely seal and inspect all 6-surfaces (top, hinge side, bottom, lock side, in the construction of the door system; each shall be sealed in accordance with manufacturer's specifications to protect against various environmental conditions. Make sure to completely seal and inspect all 6-surfaces (top, hinge side, bottom, lock side, in

front face panel(s).

and back face) with two-coat Finishing and/or re-finishing

minimum on operable must be completed

immediately after door has acclimated to the it is to be installed and within a maximum

environment

where

of 7 days.

Avoid

finishing average surfaces

after a rain humidity. to insure

or damp and during periods of higher than Conduct periodic inspections of all coated that door components are not exposed.

Inspections should occur at least once a year. surface as needed.

Reseal the

Part 5: GENERAL PERFORMANCE

5.1 Acoustical Performance: Unit scheduled for installation in opening requiring a specific noise control rating shall be clearly

product is ordered.

1-3/4" thick Molded Panel

with particleboard core is 29. (See acoustical

sound transmission class performance data for unit

noted when Series door (STC) rating

specific acoustical information.) 5.2 Thermal Performance: Unit

scheduled

for

installation

in

opening requiring a specific thermal rating shall when product is ordered. 1-3/4" thick Molded

be clearly noted Panel door with

particleboard core at R-value of 3.54. (See data for unit specific thermal information.)

thermal

performance

5.3 Fire Resistance: requiring compliance shall be clearly noted Molded Panel Series

Unit scheduled for installation in openings with national, state or local fire guidelines when product is ordered. Masonite·1-3/4" door panels have been evaluated for use

as fire doors in 20-minute locations. Labeling is the Intertek Testing services 1 Warnock Hersey

available under program. Fire

doors

require

the

use

of

a

fire

rated

frame

system

and

must

be

installed in accordance with NFPA with manufacturer or distributor for

80 guidelines. (Please limitations of use).

check

Part 6: WARRANTY 6.1 Limited 1-Year - Please check with manufacturer or distributor for current warranty terms and conditions.

Document info
Document views951
Page views951
Page last viewedSun Dec 11 06:43:54 UTC 2016
Pages324
Paragraphs11037
Words86316

Comments