X hits on this document

PDF document

NORGLIDE® M 1.57 Type S02155 - page 1 / 1

36 views

0 shares

0 downloads

0 comments

1 / 1

Technical Data Sheet

NORGLIDE® M 1.57 Type S02155

FOR INFORMATION ONLY

Data Sheet updates will not be circulated.

1. Product

:

Semi-finished NORGLIDE® M

Density

DIN 53479

g/cm3

3.75 – 4.25

Tensile Strength

DIN EN ISO 527-3

N/mm2

80

Elongation at Break

DIN EN ISO 527-3

%

10

Deformation Under Load

23oC, at 100 N/mm2, 1h

m

50

Rate of Heat Transfer

SG PA 3/1300/3022

W/m 2K

560

Service Temperature Range

Permanent

oC

-200 - +260

Intermittently

290

Coefficient of Linear Thermal

SG PA 0/1320/1025

10-5 K-1

The data listed falls within the normal range of product properties but they should not be used to establish specification limits nor used alone as the basis

of design. Polyflon Technology Limited assumes no responsibility for any advice furnished by it or for results obtained with respect to these products. All such advise is provided gratis and the buyer assumes sole responsibility for the results obtained in reliance thereon.

7. Application Related Characteristics Maximum Admissible Specific Bearing Load

Static Dynamic

Coefficient of Friction at RT Measured on Steel with 58 HRC

at 4.8 N/mm2 and 0.058 m/s at 70 N/mm2 and 0.0065 m/s

  • 2.

    Composition

  • 3.

    Components

4. Dimensions

Data are typical performance values from laboratory tests & must not be considered as a specification for product design.

Norglide® is a registered trade mark of Saint Gobain Performance Plastics

6. Component: Sliding Layer NORGLID

E® MP6 Type 510600*

Unit N/mm2 N/mm2 %

  • *

    as received

Value 530 – 680

  • 240

  • 40

  • 108

k Factor

:

Sliding bearing material is a composite material consisting of a sliding layer of NORGLIDE® MP and stainless steel backing. Both layers are firmly attached.

:

Supplied as tape in meters wound on standard cores.

Test Method DIN EN 10002 DIN EN 10002 DIN EN 10002

  • cm 2

  • *

    measured before lamination

N/mm

2

N/mm

2

:

  • a)

    NORGLIDE® MP6 Type 510600 consisting of PTFE compound with approximately 30% of filler content of glass fibres and graphite sintered into flexible stainless steel mesh, material no. 1.4401 to DIN EN 10088-2.

  • b)

    Stainless steel plate cold-rolled strip – precision style, material no. 1.4401/1.4404.

Width (nominal) Thickness

5. Component: Steel* Properties

Tensile Strength Yield Stress (23oC) Elongation at Break

Expansion

Surface Related Volume Resistance

SG PA 1/1320/1081

: :

320mm (useful 300mm) 1.57 ± 0.040mm

10-6 mm3/Nm

180 100

0.17 0.09

Unit 16, Raleigh Hall, Eccleshall, Stafford, ST21 6JL, UK tel: +44 (0) 1785 859054 fax: +44 (0) 1785 859161

e-mail: info@polyon.co.uk

www.polyon.co.uk

Document info
Document views36
Page views36
Page last viewedSun Dec 04 15:30:59 UTC 2016
Pages1
Paragraphs94
Words421

Comments