X hits on this document

PDF document

General Information 1 - page 1 / 4

13 views

0 shares

0 downloads

0 comments

1 / 4

1

Zamac NailinTM Zamac NailinTM PRODUCT INFORMATION Nail Anchor PRODUCT DESCRIPTION

SECTION CONTENTS

Page No.

The Zamac Nailin is a nail drive anchor which has a body formed from Zamac alloy. Drive nails are available in carbon or stainless steel. The anchor can be used in concrete, block, brick or stone.

A corrosion resistant Zamac alloy is used to form the anchor body with either a mushroom or flat head. The anchor can be used for light duty, tamperproof applications.

The anchor is not recommened for overhead, life-safety or sustained tensile loading applications unless special considerations are given to the allowable loads (see performance data section).

General Information...................... 1

Installation and Material Specifications ................................. 1

Performance Data.......................... 2 Design Criteria ................................4 Ordering Information.................... 4

GENERAL APPLICATIONS AND USES

• Roof Flashing

• Mechanical Attachments

• Brick Ties and Masonry Anchorage • Electrical Fixtures

• Furring Strips • Maintenance

FEATURES AND BENEFITS

  • +

    General purpose anchoring

    • +

      Installs in a variety of base materials

Zamac Nailin

APPROVALS AND LISTINGS

ANCHOR MATERIALS

Federal GSA Specification – Meets the proof load requirements of FF-S-325C, Group V, Type 2, Class 3, (superseded) and CID A-A 1925A, Type 1 (mushroom head) & Type 2 (flat head)

Zamac Alloy with Carbon or Stainless Steel Drive Nail

GUIDE SPECIFICATIONS

ANCHOR SIZE RANGE (TYP.)

CSI Divisions: 03151-Concrete Anchoring, 04081-Masonry Anchorage and 05090-Metal Fastenings. Pin Anchors shall be Zamac Nailin anchors as supplied by Powers Fasteners, Inc., Brewster, NY.

3/16" diameter x 7/8" length to 1/4" diameter x 3" length

SUITABLE BASE MATERIALS

Normal-Weight Concrete Hollow Concrete Masonry (CMU) Brick Masonry Stone

INSTALLATION AND MATERIAL SPECIFICATIONS

ANSI Drill Bit Size, dbit (in.)

3/16

1/4

1/4

CS Nail

CS Nail

SS Nail

Fixture Clearance Hole (in.)

1/4

5/16

5/16

Drive Nail

AISI 1018

AISI 1018

Type 304 SS

Head Height (in.)

7/64

9/64

3/16

Anchor Body

Zamac Alloy

Zamac Alloy

Zamac Alloy

Head Width dhd (in.)

13/32

35/64

35/64

Nail Plating

ASTM B 633, SC1, Type III (Fe/Zn 5)

N/A

MH = Mushroom Head FH = Flat Head

CS = Carbon Steel SS = Stainless Steel

Anchor

Mushroom

Flat

Mushroom

Component

Head

Head

Head

Installation Specifications

Dimension

Material Specifications

Component Material

Anchor Diameter, d

1/4" FH

1/4" MH

3/16 MH

"

Installation Guidelines

Using the proper diameter bit, drill a hole into the base material to a depth of at least 1/4" deeper than the required embedment. The tolerances of the drill bit used should meet the requirements of ANSI Standard B212.15. Blow the hole clean of dust and other material.

Insert the anchor through the fixture. Drive the nail into the anchor body to expand it. Be sure the head is seated firmly against the fixture and that the anchor is at the proper embedment. Take care not to overdrive. This anchor is not recommended for use overhead.

www.powers.com

Canada: (905) 673-7295 or (514) 631-4216

Powers USA: (800) 524-3244 or (914) 235-6300

c

Document info
Document views13
Page views13
Page last viewedMon Nov 28 22:26:11 UTC 2016
Pages4
Paragraphs631
Words1988

Comments