X hits on this document

PDF document

General Information 1 - page 3 / 4

15 views

0 shares

0 downloads

0 comments

3 / 4

3

3/16

3/4

270

560

55

110

(4.8)

(19.1)

(1.2)

(2.5)

(0.2)

(0.5)

d

hv

Tension

Shear

Tension

Shear

in.

in.

lbs.

lbs.

lbs.

lbs.

(mm)

(mm)

(kN)

(kN)

(kN)

(kN)

1 1/4

990

970

200

195

(31.7)

(4.4)

(4.3)

(0.9)

(0.9)

Zamac NailinTM

PRODUCT INFORMATION

5/8 (15.9)

360 (1.6)

655 (2.9)

70 (0.3)

130 (0.6)

3/4 (19.1)

735 (3.3)

850 (3.8)

145 (0.7)

170 (0.8)

1 (25.4)

835 (3.8)

890 (4.0)

165 (0.7)

180 (0.8)

PERFORMANCE DATA Ultimate and Allowable Load Capacities for Zamac Nailin in Hollow Concrete Masonry1,2,3

1/4 (6.4)

  • 1.

    Tabulated load values are for anchors installed in minimum 6-inch wide, minimum Grade N, Type II, lightweight, medium-weig Mortar must be minimum Type N. Masonry compressive strength must be at the specified minimum at the time of installation

  • 2.

    Allowable load capacities listed are calculated using and applied safety factor of 5.0. Anchors are not recommended for use may be necessary depending upon the application such as in sustained tensile loading applications.

  • 3.

    Anchors installed flush with face shell surface.

ht or normal-weight concrete masonry units conforming to ASTM C 90. (f'm 1,500 psi). overhead or for life safety. Consideration of safety factors of 20 or higher

Anchor

Minimum

Diameter

Embedment

Depth

Ultimate Load

f ´ m

1,500 psi (10.4 MPa)

Allowable Load

in. (mm)

lbs. (kN)

lbs. (kN)

lbs. (kN)

lbs. (kN)

3/4 (19.1)

460 (2.1)

920 (4.1)

90 (0.4)

185 (0.8)

5/8 (15.9)

570 (2.6)

1,250 (5.6)

115 (0.5)

250 (1.1)

3/4 (19.1)

790 (3.6)

1,400 (6.3)

160 (0.7)

280 (1.3)

1 (25.4)

820 (3.7)

1,400 (6.3)

165 (0.7)

280 (1.3)

1 1/4 (31.7)

865 (3.9)

1,400 (6.3)

175 (0.8)

280 (1.3)

Ultimate and Allowable Load Capacities for Zamac Nailin in Solid or Hollow Clay Brick Masonry1,2

1/4 (6.4)

  • 1.

    Tabulated load values are for anchors installed in multiple wythe, minimum Grade SW, solid clay brick masonry walls conform compressive strength must be at the specified minimum at the time of installation (f'm 1,500 psi).

  • 2.

    Allowable load capacities listed are calculated using and applied safety factor of 5.0. Anchors are not recommended for use or higher may be necessary depending upon the application such as in sustained tensile loading applications.

ing to ASTM C 62. Mortar overhead or for life safety.

must be minimum Type N. Masonry Consideration of safety factors of 20

Anchor Diameter

Minimum Embedment Depth

hv

3/16 (4.8)

f ´ m

1,500 psi (10.4 MPa)

d

in. (mm)

Ultimate Load Tension

Shear

Al Tension

lowable Load Shear

DESIGN CRITERIA Combined Loading For anchors loaded in both shear and tension, the combination of loads should be proportioned as follows:

N u N n ( ) V u V n ( ) +

1

Where:

Nu = Applied Service Tension Load Nn = Allowable Tension Load Vu = Applied Service Shear Load Vn = Allowable Shear Load

Load Adjustment Factors for Spacing and Edge Distances1 Anchor Installed in Normal-Weight Concrete

Anchor Dimension

Load Type

Critical Distance (Full Anchor Capacity)

Critical Load Factor

Minimum Distance (Reduced Capacity)

Minimum Load Factor

Spacing (s)

Tension and Shear

scr = 10d

Edge Distance (c)

Tension

ccr = 12d

Shear

ccr = 12d

F N s

= F v s = 1 . 0

F F N c Vc

= 1.0 = 1.0

s c c min = 5d min = 5d min = 5d

F N s

= F v s = 0 . 5 0

F F N c Vc

= 0.80 = 0.50

1. Allowable load values found in the performance data tables are multiplied by reduction factors when anchor spacing or edge distances are less than critical distances. Linear interpolation is allowed for intermediate anchor spacing and edge distances between critical and minimum distances. When an anchor is affected by both reduced spacing and edge distance, the spacing and edge reduction factors must be combined (multiplied). Multiple reduction factors for anchor spacing and edge distance may be required depending on the anchor group configuration.

c

www.powers.com

Canada: (905) 673-7295 or (514) 631-4216

Powers USA: (800) 524-3244 or (914) 235-6300

Document info
Document views15
Page views15
Page last viewedFri Dec 09 16:22:47 UTC 2016
Pages4
Paragraphs631
Words1988

Comments