X hits on this document

92 views

0 shares

0 downloads

0 comments

4 / 24

ALL 4 CYL 390 ALL 6 CYL 590

CUB-751FP CUB-101FP CUB-151FP

CUB-752FP CUB-102FP CUB-152FP

750 1000 1500

ALL 6 CYL 830

CUC-151FP

CUC-152FP

1500

C7 ACERT

FP101-001 FP151-001

FP102-001 FP152-001

1000 1500

C9 ACERT

CATV-151

CATV-152

1500

C11 ACERT C13 ACERT

TF151-008

TF152-008

1500

C15 ACERT

TF151-009

TF152-009

1500

C-10 C-12

TF121-000

TF122-000

1250

C-9 Non ACERT C-15 Non ACERT C-16 Non ACERT

CATV-151

CATV-152

1500

1674

CATB-151

CATB-152

1500

1693 & D343

CATC-151

CATC-152

1500

1693T & 1693TA

CATC-151-S

CATC-152-S

1500

3013 1.5L 3014 2.0L

FP531-003

FP532-003

530

3024 2.22L

FP531-003

FP532-003

530

3034 2.95L

FP531-001

FP532-001

530

3044 3.3L

PF531-001

PF532-001

530

4

22mm

Replace 1”NPT plug in the right rear of the engine block

Part Number

Part Number

Engine Model

120 Volts

240 Volts

Inserts in the freeze plug right rear of the block

Replace any of the 1 5/16”plugs in rear of oil Check Exhaust

cooler on the right hand side of the engine

Routing

1 5/16” STOR

1” NPT

  • *

    If supplemental oil heating is desired, this column gives the correct thread size in oil pan. See NOTE on page 11.

Kim Hotstart Manufacturing Company, Inc.

P.O. Box 11245

Spokane, WA 99211-0245

In-Block

Direct Immersion Heaters

685T & I

AC-101

AC-102

6138LT,T & I

CATV-151

CATV-152

Note: In-block heaters are complete with 2-wire w/ground 6 foot HPN cord and plug. For cord replacements or “Y” thermocord energy saver, please reference page 12.

1000 1500

Replaces 1”thread-in plug on the oil cooler at rear of the engine on the right side. Note that not all of the engines have this opening.

Case/IH – Agricultural

Inserts in any of the freeze plugs right side of engine

22mm

Caterpillar

Replace 44mm frost plug on right hand side of engine just below the turbo charger.

YES

Replace 1 3/16”plug in rear of the oil cooler on the right hand side of the engine

Replaces the 1”threaded plug in the oil cooler bonnet

YES

Replaces the 1 1/2”thread-in plug on the right side of the engine

Replaces water jacket access plate on the left side of the engine

Replaces water jacket access plate on the left side of the engine

Replaces 40mm core plug on the front,left side of the engine

Replaces 40mm core plug on the front,left side of the engine

Replaces 50mm core plug located at back of head

Mounts in“football shaped”opening on the right of the engine

1” NPT

670T & I

25000 (844 CID)

Heat Shield

Oil Heater

Required

Thread Size*

Watts

Product Image

Application Information

Allis Chalmers

C-9 Only: C-15, C-16:

Mount in rear face of block Mount in rear oil cooler bonnet from the back end

Document info
Document views92
Page views98
Page last viewedThu Dec 08 17:00:36 UTC 2016
Pages24
Paragraphs1912
Words7545

Comments