X hits on this document

103 views

0 shares

0 downloads

0 comments

5 / 24

3046 5.0L

PF531-000

PF532-000

530

3054 3.99L 3054B 4.23L

PER-751FP PER-101FP

PER-752FP PER-102FP

750 1000

3054C

PER-751FP

PER-752FP

750

3056 6.0L

PER-151FP

PER-152FP

1500

3114 3116 3126

FP101-001 FP151-001

FP102-001 FP152-001

1000 1500

3176 10.3L through 1995

DD8L-101 CAT-12015 TF151-001

DD8L-102 CAT-12023 TF152-001

1000 1250 1500

3176 10.3L 1996 and later

TF121-000

TF122-000

1250

3196 12.0L

TF121-000

TF122-000

1250

3204 all 1100 series

CATX-751 CATX-101

CATX-752 CATX-102

750 1000

3208 — 2 heaters with a single cord

CATX-2-751-Y

CATX-2-752-Y

1500 total

3208 Recommended Aftermarket Installation

JD3/4-101IN JD1-101IN JD3/4-151IN JD1-151IN

JD3/4-102IN JD1-102IN JD3/4-152IN JD1-152IN

1000 1000 1500 1500

3304 3306

DD8L-101 CAT-12015 TF151-001

DD8L-102 CAT-12023 TF152-001

1000 1250 1500

3406C/E 14.6L

AC-101 CATV-151

AC-102 CATV-152

1000 1500

3406 & 3408 except 1998 Adem 2

AC-101 CATV-151

AC-102 CATV-152

1000 1500

3406E 1998 Adem 2 engines only

TF151-002

TF152-002

1500

3406E ADEM 3 and ADEM 2000 engines

AC-101 CATV-151

AC-102 CATV-152

1000 1500

Mounts in the 1 1/2”freeze plug on the right side of the engine

Replaces the core plug on the right side of the engine just below the turbocharger

YES

11/16”X12

Replaces the 3/4”plug on the right side of the engine just below the head.

1” NPT

Replaces the 1”threaded plug in the oil cooler bonnet

YES

11/16”X12

Replaces 1”threaded plug in oil cooler bonnet

YES

11/16”X12

Mounts in 1 1/4”freeze plug at right rear of engine with element straight up in 12 O’clock position.

Mounts in the 1 1/4”freeze plug opening on the right side of the engine

Replaces the core plug on the right side of the engine just below the turbocharger

Use on industrial engines when clear access is available. Replaces any core plug - one on each side of the engine

Replaces any of the 3/4”or 1”plugs on the water transfer casting (right front of the engine).3/4”use JD3/4 — 1”use JD1

22mm

  • *

    If supplemental oil heating is desired, this column gives the correct thread size in oil pan. See NOTE on page 11.

Customer Support: (509) 536-8660

Toll-Free FAX: (800) 224-5550

www.kimhotstart.com

5

Heat Shield

Oil Heater

Required

Thread Size*

Replaces 35mm core plug located at rear of engine, left side

Replaces the 3/4”plug on the left side of the engine

Replaces 1”thread-in plug in the rear of the oil cooler bonnet on the right side of the engine

1” NPT

1” NPT

1” NPT

1” NPT

Caterpillar — Continued

Replaces 1”thread-in plug in the rear of the oil cooler bonnet on the right side of the engine

Replaces the 1”threaded plug that points downward on the top of the rear of the oil cooler bonnet

Replaces 1”thread-in plug in the rear of the oil cooler bonnet on the right side of the engine

YES

In-Block

Direct Immersion Heaters

Note: In-block heaters are complete with 2-wire w/ground 6 foot HPN cord and plug. For cord replacements or “Y” thermocord energy saver, please reference page 12.

Application Information

Engine Model

Product Image

Watts

Part Number

Part Number

120 Volts

240 Volts

Document info
Document views103
Page views109
Page last viewedSat Dec 10 10:32:07 UTC 2016
Pages24
Paragraphs1912
Words7545

Comments