X hits on this document

16 views

0 shares

0 downloads

0 comments

4 / 7

  • STC: [SPECIFIER: Enter job spec]

C.

Furnish

written

documentation

that the

  • 2.

    Acoustic performance to be verified by testing for conformance with [NOTE TO SPECIFIER: Select any as applicable)]

    • ASTM E 90

    • ASTM E 1425

    • AAMA 1801

STC and OITC ratings shall be derived from ASTM E 413 and ASTM E 1332, respectively. (Manufacturer to provide test results on

E.

request). Impact Resistance

(Fixed

Window

Only):

Windows

shall

be

tested

for

conformance

both

with the requirements of [NOTE TO SPECIFIER: Select either of the following as applicable]

  • AAMA 506

  • ASTM E 1996 (test method: ASTM

    • 1886)

      .

(Manufacturer to provide test results on request).

or

E

    • 1.07

      Submittals

      • A.

        Enhanced

Drawings:

Upon

request the

window manufacturer may submit elevation drawings, cross section drawings with basic installation guidelines. Anchorage details are to be determined by others.

B.

Product data:

manufacturer’s specifications,

test

reports

from

an

AAMA-accredited

C.

laboratory, and standard details conformance with specifications. Samples: one sample of specified

verifying

finish for

aluminum and other by the architect.

samples

as

requested

windows for the project conform AAMA/WDMA/CSA 101/I.S.2/A440-05 AAMA/WDMA/CSA 101/ I.S.2/A440-08

to or as

applicable.

  • D.

    Furnish written documentation that the windows for the project conform to energy efficiency requirements as described in Section 1.07B above.

  • E.

    Manufacturer’s warranties

1.

2.

3.

4.

Windows: If installed per manufacturer’s instructions, windows shall be warranted for five years (one year on moving parts) from date of sale against defects in material or workmanship under normal use. Sealed insulated glass (IGU): IGU shall be warranted for ten years against obstruction of vision resulting from failure of the hermetic seal, excluding that caused by breakage or abuse. Units containing muntin bars and/or capillary tubes shall be warranted for three years, and laminated glass for five years. 10-year pass-through warranty against failure of the polymer on aluminum extrusions having a mechanically locked pour and debridged thermal break. Aluminum organic coatings shall be covered by a limited warranty

NOTE TO SPECIFIER: Select the ap- plicable option from the following.

  • for 15 years against chipping, peeling cracking, blistering, fading or chalking, as required per AAMA specification AAMA 2605

for

10

years

chipping,

peeling

    • 1.08

      Quality Assurance NOTE TO SPECIFIER: Delete those of fol- lowing paragraphs A through E that do not apply to the project requirements.

      • A.

        Submit for pre-bid qualification approval ten days prior to the bid opening:

        • 1.

          One sample window representing the window being bid with color being the only exception.

        • 2.

          Valid test reports not more than four years from test date (at time of submittal) from an AAMA-accredited laboratory confirming conformance to Paragraph

        • 1.07

          test results.

      • B.

        Submit bids based only on pre-qualified “equal” as confirmed in a pre-bid written addendum.

1.09

cracking, blistering, fading or chalking, as required per AAMA

specification AAMA 2604

for

5

years

against

chipping,

peeling, cracking or blistering, as required per AAMA specification AAMA 2603.

Delivery, Storage and Handling

A.

Handle

windows

and

accessories

in

accordance with AAMA CW-10.

  • B.

    Protect the windows from the elements, construction activities and other hazards until project completion.

  • C.

    Install per AAMA IPCB (08).

Page 4 of 7

M-85 Spec – Rev. 9/10

Document info
Document views16
Page views16
Page last viewedFri Oct 28 16:37:16 UTC 2016
Pages7
Paragraphs754
Words3644

Comments