X hits on this document

19 views

0 shares

0 downloads

0 comments

5 / 7

  • II.

    PRODUCTS:

    • 2.01

      Acceptable Window Manufacturers

      • A.

        Windows shall be the “M85 Series” as manufactured by Wojan Window and Door Corporation, Charlevoix, Michigan. The “M85 Series” is a…

NOTE TO SPECIFIER: Select which of the following is applicable to the project.

  • single hung, consisting of an operable lower sash and a fixed upper sash

  • horizontal sliding consisting of NOTE TO SPECIFIER: Select the ap- plicable option from the following.

    • -

      SV - an operable (left or right) sash and a fixed opposing sash

    • -

      EV - two operable sash and a fixed center sash

    • -

      CV - an operable center sash and two fixed end sash

  • fixed window

  • type with thermally improved frame and/or

sash. The specifications and materials for the “M85 Series” are as follows:

2.02

Materials

  • A.

    Sash and frame members

    • 1.

      Aluminum shall be of proper alloy for commercial window construction. All extruded sections shall be of 6063-T6 aluminum alloy.

    • 2.

      Main frame and sash members shall be a nominal thickness as required by AAMA/WDMA/CSA 101/I.S.2/A440-05 or AAMA/WDMA/CSA 101/I.S.2/A440-

C.

08 as

applicable.

2.663”

in depth.

Mainframe

shall

be

B.

Finish

1.

Application: on clean extrusions free from significant surface blemishes or scratches on exposed surfaces visible when the installed window’s operating sash is closed.

D.

NOTE TO SPECIFIER: Select from the following versions of paragraph 2 to meet project requirements.

  • 2.

    Coatings shall be organic and shall meet the requirements of: NOTE TO SPECIFIER: Select one of the following to meet project re- quirements.

    • AAMA 2603

Page 5 of 7

M-85 Spec – Rev. 9/10

  • AAMA 2604

  • AAMA 2605

Color shall be:

NOTE TO SPECIFIER: Select from the following to meet project re- quirements; must agree with specifi- cation selected above.

  • Standard

color

electrostatically-

applied baked-on polyester to meet or exceed AAMA 2603.

Standard h i g h - p e r f o r m a n c e color f l u o r o p o l y m e r ( K y n a r ® ) exceed AAMA 2605. to meet or

NOTE TO SPECIFIER: Minimum or- der quantity may apply below.

H i g h - p e r f o r m a n c e f l u o r o p o l y m e r ( K y n a r ® ) t o m e e t o r e x c e e d A A M A 2604. Custom color/finish to match color

2.

sample chip furnished by customer to conform to AAMA 2603, 2604 or 2605 as applicable. Coatings shall be anodic (anodized) and shall meet the requirements of AAMA 611. Color shall be:

NOTE TO SPECIFIER: Select from the following to meet project re- quirements.

  • Standard color

NOTE TO SPECIFIER: Minimum or- der quantity may apply below.

  • Non-standard color/finish, or custom color/finish to match color sample chip furnished by customer.

Thermal break: Main frames and sash members are to be extruded aluminum having a structural thermal barrier. Azo- Brader technology shall be used as part of

the

aluminum

quality

process

and

production of fenestration members create a mechanical lock in the polymer.

to

Hardware 1. Locks shall consist of

NOTE TO SPECIFIER: Select the ap- plicable option from the following.

a cam-type sweep interlocking meeting rail.

lock

at

the

2.

  • an extruded self-locking spring-loaded locking bar (Not available center vent HS).

Balances (single hung): Sash will be balanced by:

Document info
Document views19
Page views19
Page last viewedMon Dec 05 08:50:45 UTC 2016
Pages7
Paragraphs754
Words3644

Comments