X hits on this document

22 views

0 shares

0 downloads

0 comments

6 / 7

E.

F.

  • Class I block-and-tackle type balance

system. Balances shall hold the sash stationary in any position along the full range of

sash

travel.

Balances

shall

meet

the

Interior and exterior lites of the IGU shall be…

NOTE TO SPECIFIER: Select which of the following is applica- ble to the project.

3.

requirements of AAMA 902. Rollers (horizontal sliding): consist glass reinforced nylon housing, with ball bearing roller per roller assembly.

of 1

Weatherstripping shall 701/702 specification for

conform to AAMA weatherstrip.

Glass and glazing 1. Construction

glass units (IGU) shall be t h i c k n e s s ( 3 / 4 " S H & H S ) a. Insulating 1” overall 3 / 1 6 o r ¼ with two lites of DS, glass,

the exterior lite of which shall be…

NOTE TO SPECIFIER: Select which of the following is applica- ble to the project.

  • clear annealed (conforming to ASTM C 1036)

  • low-E coated with a non/pyrolytic coating (surface #2) (conforming to ASTM C 1048)

  • tinted

color]

[SPECIFIER:

Enter

tint

  • obscure pattern glass

  • tempered (conforming to ASTM C 1048 or CPSC16CFR1201 Safety Standard for Architectural Glazing Materials as applicable)

  • laminated glass (conforming to ASTM C 1172)

NOTE TO SPECIFIER: Select which of the following is appli- cable to the project.

and the interior lite of which shall be…

  • clear annealed (conforming to ASTM C 1036)

  • low-E coated with a non/pyrolytic coating (surface #3) conforming to ASTM C 1048)

  • obscure pattern glass

  • tempered (conforming to ASTM C 1048 or CPSC16CFR1201 Safety Standard for Architectural Glazing Materials as applicable)

  • laminated glass (conforming to ASTM C 1172)

  • separated by aluminum spacers

and desiccated.

Perimeter seal-

ant shall be polyurethane. separated by warm-edge

spacers

and desiccated.

Perimeter seal-

ant shall be polyurethane. The interior space between

interior

and exterior lites shall be filled with

2.

NOTE TO SPECIFIER: Select which of the following is applica- ble to the project.

  • argon (90%) / air (10%) mixture

  • air (100%)

Operable sash glazing

    • a.

      Glass in the operable sash shall be marine glazed at the factory. All lites are to be glazed from the interior to enable replacement from the interior.

    • b.

      The single hung operable sash shall be side-loaded and removable from the inside for ease of maintenance.

    • c.

      The horizontal sliding operable sash be top loaded and removable from the inside for ease of maintenance.

  • 3.

    Fixed glazing on operable windows: The fixed lite shall be marine glazed at the factory.

  • 4.

    Fixed glazing on fixed windows: The fixed lite shall be butyl tape glazed at the factory using a reusable aluminum mechanical glazing bead. Fixed lites may be fitted with spandrels in lieu of glazing if so specified.

  • G.

    Screens

    • 1.

      Screen frame shall be of NOTE TO SPECIFIER: Delete the fol- lowing if not applicable to the project.

      • aluminum extrusion.

      • roll-formed aluminum. Finish shall match the main frames and sash.

    • 2.

      Insect screening shall be NOTE TO SPECIFIER: Delete the fol- lowing if not applicable to the project.

      • fiberglass cloth

      • aluminum wire

      • pet screen cloth

Page 6 of 7

M-85 Spec – Rev. 9/10

Document info
Document views22
Page views22
Page last viewedSat Dec 10 15:24:55 UTC 2016
Pages7
Paragraphs754
Words3644

Comments