X hits on this document

PDF document

WEDNESDA , APRIL 13 - MORNING Technical and Business Sessions - page 8 / 100

576 views

0 shares

0 downloads

0 comments

8 / 100

electronics

THURSDA , APRIL 14 - MORNING Technical and Business Sessions

TIME

SESSION TITLE, DESCRIPTION, AND ROOM

D0-06A

D0-03A

D0-03C

D0-03B

CAD/CAM/CAE Technology (B101)

In-Vehicle Networks (AE305)

Safety Critical Systems (Part 1 of 2) (AE300)

Systems Engineering (Part 1 of 2) (AE312)

Technical papers and/or presentations offered in this session will portray the latest developments and proposals for In-Vehicle Networks. Typical subjects covered are: new protocols, gateways, vehicle control, message handling, X-by-wire, diagnostics, off-board connectivity and vehicle-to-vehicl

e

or vehicle-to-infrastructure communications.

The focus of the session is on system safety analysis and design of safety-critical systems employing electronic controls. Topics include: implementation of safety-relevant systems, fail-safe strategies, distributed fault tolerant systems and hazard analysis. Application areas include: automotive active

safety and alternative energy systems as well as avionics and mission management. Finally, the session addresses application of new or revised safety standards such as ISO 26262 and DO-178C.

This session addresses automotive requirements, high level system design, cost analysis, simulation, modeling, testing, and validation. System includes components, sub assemblies, computer based controllers, hardware and software. The session focuses on intelligent and efficient approaches to analysis, design (not detailed design), modeling, measurement, document management and optimizing performance. Topics on effect of cost, and human machine interface are covered.

8:00 a.m. - 11:40 a.m.

8:00 a.m. - 12:00 p.m.

8:00 a.m. - 10:20 a.m.

8:00 a.m. - 10:40 p.m.

Organizers: Randy Gu, Oakland Univ.; Yu J. Teng, Chrysler Group LLC; William J. Altenhof, Univ. of Windsor; Yun Lu, Chrysler Group LLC; Pilaka Murty, WTAMU

Chairpersons: William Altenhof, Univ of Windsor

Organizers: Richard D. Means, Mark Zachos, DG Technologies

Chairpersons: James Lawlis, Ford Motor Co

Organizers: Joseph G. D’Ambrosio, General Motors R&D Ctr.; Brian T. Murray, United Technologies Research Center; Markus Plankensteiner, TTTech Automotive Gmbh

Chairpersons: Markus Plankensteiner, TTTech Automotive Gmbh

Organizers: Subramaniam Ganesan, Oakland Univ.; Ken Rao, IBES Inc.

Chairpersons: Subramaniam Ganesan, Oakland University; Ken Rao, IBES Inc

Accurate Simulation of Door Side Intrusion in Automotive Structures with Progressive Fracture

Automatic Gateway Prototype Generation for Optimization of E/E-Architectures Based on high-Level Models

(2011-01-1070)

(2011-01-1029)

Naga A. Narayana, Nissan Technical Center NA Inc.

Oliver Sander, Jannik Merz, Juergen Becker, Karlsruhe Institute of Technology (KIT); Clemens Reichmann, aquintos Gmbh

10:40 a.m.

Application of Failure Plastic Strain to Quasi- Static Finite Element Analysis for Projection Weld and Strain-based Spot Weld Evaluation

ESCAN - An Open Source, high Bandwidth, Event Scheduled Controller Area Network

(2011-01-1074)

(2011-01-1041)

hwawon Lee, Parvath Police, General Motors Company

Anthony Williams, Christopher Quigley, James Finney, Warwick Control Technologies Ltd.

Integrated CAD/CAE Functional Design for Engine Components and Assembly

A New high-Speed Bus Topology LAN Protocol Compatible with CAN

(2011-01-1071)

(2011-01-1043)

Carlo Rosso, Cristiana Delprete, Elvio Bonisoli, Stefano Tornincasa, Politecnico di Torino

Ryo Kurachi, hiroaki Takada, Nagoya Univ.; Masanobu Nishimura, Satoshi horihata, Autonetworks Technologies

Finite Element Study on Piston Assembly Dynamics in Multicylinder Internal Combustion Engine (Written Only -- No Oral Presentation)

ADACS: Advanced Diagnosis for Time- Triggered Automotive Communication Systems

(2011-01-1075)

(2011-01-1044)

Ravindra R. Malagi, Gogte Institute of Technology; Shivakant N. Kurbet, B.V.V’s Basaweshwar Engineering College; N. Gowrishenkar, India Piston Rings, Ltd.

Eric Armengaud, Allan Tengg, Virtual Vehicle; Roland Lieger, Erwin Kristen, Austrian Institute of Technology

11:00 a.m.

11:20 a.m.

11:40 a.m.

10:01 p.m.

Intelligent CAD Tool to Solve Challenges in the Design of Orbiting EDM Electrode (Written Only -- No Oral Presentation)

(2011-01-1073) Tutik Sriani, hideki Aoyama, Keio Univ.

10:02 p.m.

Application of 3-D CFD on Mechanical and Acoustical Performance of an Automotive Exhaust System (Written Only -- No Oral Presentation)

(2011-01-1068) Somnath Sen, TATA Technologies Ltd.

10:04 p.m.

Scanning Frequency Ranges of harmonic Response for a Spot-Welded Copper- Aluminum Plate Using Finite Element Method (Written Only -- No Oral Presentation)

(2011-01-1076)

Randy Gu, Oakland University; Leonid C. Lev, General Motors Company; Lianxiang Yang, Oakland University

Planned by Body Engineering Committee / Automobile Body Activity

The papers in this session are available in SAE Technical Paper Collection, COLL-TP-00131, and also individually. To purchase visit collections.sae.org

The papers in this session are available in SAE Technical Paper Collection, COLL-TP-00127, and also individually. To purchase visit collections.sae.org

Planned by Electrical and Electronic Systems Committee / Automobile Electronics Activity

Planned by Electrical and Electronic Systems Committee / Automobile Electronics Activity

The papers in this session are available in SAE Technical Paper Collection, COLL-TP-00126, and also individually. To purchase visit collections.sae.org

The papers in this session are available in SAE Technical Paper Collection, COLL-TP-00129, and also individually. To purchase visit collections.sae.org

56

SAE 2011 World Congress

Document info
Document views576
Page views576
Page last viewedTue Jan 24 11:51:50 UTC 2017
Pages100
Paragraphs7750
Words67338

Comments