X hits on this document

207 views

0 shares

15 downloads

0 comments

2 / 2

Roll length

:

20 metre

Roll width

:

1 metre (20 sq m)

Thickness

:

1.5mm overall

Weight per roll : Minimum overlaps

32 kg gross 50mm side and end

Recommended application 4°C to 55°C

temperature Storage

:

(see notes below) Store upright in dry conditions below 40°C

Equipment by Others Soft broom, Stanley knife, brush or roller for priming, stiff broom and airline for cleaning surfaces.

Application Measures should be taken to ensure that all surfaces are free from ice. frost or condensation. Concrete blinding under base slab should be surface dry, free from standing water, and laid to a regular surface free from sharp protrusions and hollows. Horizontal surfaces under base slabs do not usually require priming before applying the membrane.

Vertical faces shall be smooth, regular, dry and free from nails and primed with one coat of Servicised B Primer HC applied by brush or roller, at a rate of 10-12 sq m/litre depending on the porosity of the surface, and allowed to completely dry before the application of the Bituthene 1000X HC. Brickwork shall be flush pointed or rendered to provide a smooth surface before priming. Bituthene 1000X HC shall be laid by peeling back the protective release paper and applying the adhesive face on to the prepared surface. The material should be brushed on to the surface to ensure good initial bond.Adjacent rolls are aligned and overlapped 50mm minimum at side and ends and well rolled with a firm pressure using a Servicised Lap Roller to ensure complete adhesion and continuity between the layers. Bituthene 1000X to extend 300mm beyond line of retaining walls to allow continuity with the vertical application. Anypunctures or damaged areas should be cleaned and patched using Bituthene 1000X with 50mm laps all round. Following the application care should be taken to prevent damage by following trades by using a 25mm screed as horizontal protection or Servipak boards spot bonded with Pak Adhesive. Vertical faces to be protected if required against damagefrom backfilling and fixing of reinforcement by using Korkpak, Servipak or other boards recommended by Servicised Ltd. spot bonded with Pak Adhesive.

Handling Precautions Bituthene 1000X HC has no health hazard when used in accordance with our standard application instructions.

SVD04

MAY04

R-00

00

Servicised B Primer HC is flammable with a Flash Point 25°C-30°C and should be used in well ventilated areas away from sources of ignition. Inhalation should be avoided and undried material prevented from coming into contact with skin. The use of protective clothing, goggles, barrier creams and rubber gloves is required. At the end of each working period the skin should be thoroughly cleansed with soap and warm water or a resin removing cream. The use of solvents for cleaning skin is to be avoided. If any irritation or redness is apparent obtain medical advice immediately. In case of accidental eye or mouth contact flush with water and obtain medical advice immediately.

Health and Safety For further information and handling precautions refer to the following company material health and

safety data sheets: Servicised B Primer HC Bituthene Mastic HC Pak Adhesive

TSO/HS 1 TSD/HS18 TSD/HS 4

Specification

Bituthene 1000X HC preformed, self-adhesive membrane shall be laid on to smooth concrete blinding and on to walls primed with Servicised B Primer HC and applying the preformed membrane, sticky side downwards, to give well rolled 50mm overlaps, laid strictly in accordance with the manufacturerÓā∂s instructions and supplied by Servicised Ltd., Ajax Avenue, Slough, Berkshire SL1 4BH, United Kingdom. Tel. Nos: 0753-692929. Telex: 846966 SERVCD G. Fax: 0753-691623.

Performance & Testing Compliance.

Property Tape Strength

Test Method Typical Results

ASTM D638 Long 4.2 N/mm Trans 4.8 N/mm

Tensile Strength

ASTM D638 Long 42 N/mm2 Trans 48 N/mm2

Elongation Film

ASTM D638 Long 210% Trans 160%

Tear Resistance ASTM D1004 Long 340 N/mm Trans 310 N/mm

Adhesion to Primed Concrete

ASTM D1000 Long 340 N/mm Trans 310 N/mm

Adhesion to Self

ASTM D1000

1.8 N/mm

Puncture

ASTM E154

220 N 65 mm

Resistance

ASTM D570

after 24 hrs

0.14%

after 35 days

0.95N

ASTM D543

Conforms

0.3 g/m2/24 hrs

Water

Resistance

Environmental Resistance

Moisture Vapour Transmission Rate

ASTM E96

BITUTHENE 1000X HC complies with the relevant section of the following national standards: CP 102: 1973, CP8102: 1990 / Building Regulations 1985 Clause C4 / Building Regulations (NI) 1985 clause C6 / Building Standards (Scotland) Regulations 1981, 1982, 1984 Regulations B2, G8, G9.

Document info
Document views207
Page views221
Page last viewedFri Dec 02 20:43:22 UTC 2016
Pages2
Paragraphs73
Words1367

Comments