X hits on this document

142 views

0 shares

0 downloads

0 comments

32 / 40

Operating JVC’s Audio/Video Components

CD changer

After pressing CD-DISC, you can perform the following operations on a CD changer:

1 6, 7/P:

Select the number of a disc installed in a CD changer.

After pressing CD, you can perform the following operations on a CD changer:

1 10, +10:

Select a track number directly. For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.

3: 4:

¢: 7: 8:

Start playing. Return to the beginning of the current (or previous) track. Skip to the beginning of the next track. Stop playing. Pause playing. To resume, press 3.

Example:

  • Selecting disc number 4, track number 12, and starting playback.

1

Press CD-DISC, then press 4.

2

Press CD, then press +10, 2.

If your CD changer is of 200-disc loading capability (except for XL-MC100 and XL-MC301), you can do the following operations using the number buttons after pressing CD.

1 2 3

Select a disc number. Then select a track number (always enter two digits). Press 3 to start playback.

Examples:

  • Selecting disc number 3, track number 2, and starting playback. Press 3, then, 0, 2, then 3.

  • Selecting disc number 10, track number 5, and starting playback. Press 1, 0, then, 0, 5, then 3.

  • Selecting disc number 105, track number 12, and starting playback.

Press 1, 0, 5, then 1, 2, then 3.

Note:

It is required to press each button within 4 seconds in the above procedure.

30

Operating Video Components

IMPORTANT:

To operate JVC’s video components using the supplied remote control:

  • Some JVC’s VCRs can accept two types of the control signals— remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the target VCR is set to code “A.”

  • When using the remote control, aim the remote control directly at the remote sensor on each component, not on the receiver.

  • Refer also to the manuals supplied with your components.

VCR You can always perform the following operations:

STANDBY/ON

VCR:

Turn on or off the VCR.

VCR CH +/–:

Change the TV channels on the VCR.

After pressing VCR, you can perform the following operations on the VCR:

3: REW: FF: 7: 8: REC PAUSE:

Start playing. Rewind the tape. Fast-forward the tape. Stop playing, recording, rewind and fast forward. Pause playing and recording. To resume, press 3. Enter recording pause. To start recording, press this button then 3.

DVD player You can always perform the following operation:

STANDBY/ON

DVD:

Turn on or off the DVD player.

After pressing DVD, you can perform the following operations on the DVD player:

3: 4: ¢: 7: 8:

Start playing. Return to the beginning of the current (or previous) chapter. Skip to the beginning of the next chapter. Stop playing. Pause playing. To resume, press 3.

After pressing DVD, these buttons can be used for the DVD menu operations.

4

2

6

Note:

MENU

For detailed menu operations, refer to the instructions supplied with the discs or the DVD player.

7/P

ENTER

10

8

TV

Set TV/CATV selector to “TV.” You can always perform the following operations:

STANDBY/ON

TV/CATV: Turn on or off the TV.

TV/CATV CH +/–: TV VOLUME +/–: TV/VIDEO:

Change the channels. Adjust the volume. Set the input mode (either TV or VIDEO).

After pressing TV SOUND, you can perform the following operations on the TV:

1 – 9, 0, 100+ (+10): Select the channels.

RETURN (10):

Alternate between the previously selected channel and the current channel.

Document info
Document views142
Page views137
Page last viewedSun Dec 11 06:32:21 UTC 2016
Pages40
Paragraphs2251
Words16130

Comments