X hits on this document

14 views

0 shares

0 downloads

0 comments

2 / 2

Thermalbond V2100 Standard Roll Sizes

Sealant No.

**Thickness in. (mm)

Length ft. (m)

V2104

1/8 (3.2)

50 (15.2)

V2106

3/16 (4.8)

50 (15.2)

V2108

1/4 (6.4)

50 (15.2)

V2110

5/16 (7.9)

25 (7.6)

V2112

3/8 (9.5)

25 (7.6)

V2116***

1/2 (12.7)

20 (6.1)

3" I.D. Cores

Widths: 1/4" to 56"

(Varies with Gauge)

Color: Black

Thermalbond V2100

Silicone

**Hard metric sizes available subject to minimum quantity orders. ***Minimum order quantity may apply.

  • Also available in gray color. Contact your local area manager.

Storage: Material should be stored at 70˚F (21°C), 50% relative humidity. Application Guide: Contact surfaces must be thoroughly cleaned and dry. Once Thermalbond® V2100 is applied, it cannot be removed and reused, so position sections carefully, making sure product is in contact with all surfaces. If unit is misaligned, remove used Thermalbond V2100, discard and repeat application with new material. Test this product for system compatibility as individual application conditions can affect results.

Typical Physical Properties

Thermalbond V2100

Insulating Glass

Thermalbond V2100

Silicone

Property

Value

Test Method

Density: lbs./cu. ft. (kg/m3)

31 (497)

ASTM D-1667

Force to Compress 10%: psi (kPa)

31 (214)

ASTM D-1667

Hardness: Shore A

35

ASTM D-2240

Tensile Strength: psi (kPa)

180 (1241)

ASTM D-412

Elongation: %

125

ASTM D-412

Dynamic Tensile Adhesion: psi (kPa)

55 (379)

NTP-11

Dynamic Shear Adhesion: psi (kPa) 15 minute dwell

40 (276)

Static Shear Adhesion: Hours 1 psi load

2000+

Thermal Conductivity K factor: BTU•in/hr•ft2•°F (w/m•˚C)

.55 (0.08)

Migratory Staining of Acrylic Enamel: 200 hours of ultraviolet at 140˚F

No Staining

Recommended Service Temp.:

-40˚F (-40°C) to 180˚F (82°C)

Recommended Application Temp.:

60˚F (16°C) to 125˚F (52°C)

NTP is Norton Test Procedure. Parameter values are not guaranteed and will differ from lot to lot. For specification writing, contact Saint-Gobain Application Engineering Dept.

15 minute dwell

NTP-5

NTP-57

ASTM C-518

ASTM D-925

Thermalbond V2100

Silicone

NOTE: Thermalbond V2100 is a SPACER material and not intended to be a structural component.

Thermalbond®

is a registered trademark.

Distributed By:

Saint-Gobain Performance Plastics One Sealants Park Granville, NY 12832 1-800-724-0883 (518) 642-2200 Fax: (518) 642-2793 www.nortonfoam.com

Limited Warranty: For a period of 6 months from the date of first sale, Saint-Gobain Performance Plastics Corporation warrants this product(s) to be free from defects in manufacturing. Our only obligation will be to provide replacement product for any portion proving defective, or at our option, to refund the purchase price thereof. User assumes all other risks, if any, including the risk of injury, loss or damage, whether direct or consequential, arising out of the use, misuse, or inability to use this product(s). SAINT-GOBAIN PERFORMANCE PLASTICS DISCLAIMS ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

NOTE: Saint-Gobain Performance Plastics Corporation does not assume any responsibility or liability for any advice furnished by it, or for the performance or results of any installation or use of the product(s) or of any final product into which the product(s) may be incorporated by the purchaser and/or user. The purchaser and/or user should perform its own tests to determine the suitability and fitness of the product(s) for the particular purpose desired in any given situation.

SPE-5067-5M-0607-SGCS www.nortonfoam.com

©2007 Saint-Gobain Performance Plastics Corporation

Document info
Document views14
Page views14
Page last viewedTue Oct 25 21:21:06 UTC 2016
Pages2
Paragraphs119
Words748

Comments