X hits on this document

34 views

0 shares

0 downloads

0 comments

15 / 16

Paint Preparation

Catalyst Mix Ratio

Paint Gun

Application

Dry Time

Stir Prime Time, do not shake. Mix appropriate shade of Prime Time using 3030 series toners. Shades closely resemble Dupont® Value Shade® system. Catalyzed Prime Time has an 8 hour pot life. Catalyze appropriate amount to meet job requirements.

Shake or stir Bumper and Cladding Coat. Pour appropriate amount into gun to meet job requirements.

Stir Prime Time, do not shake. Mix appropriate shade of Prime Time using 3030 series toners. Shades closely resemble Dupont® Value Shade® system. Catalyzed Prime Time has an 8 hour pot life. Catalyze appropriate amount to meet job requirements.

Stir Black Cat, do not shake. If desired, Black Cat may be thinned with water up to 5% by volume.

Catalyzed Black Cat has an 8 hour pot life. Catalyze appropriate amount to meet job requirements.

Mix 3103 catalyst with Prime Time 2% by weight. (weight of paint) x .02= weight of catalyst For example, if you are using 100 grams of Prime Time, add 2 grams of 3103 catalyst. If no scale is available, then mix 2 teaspoons of catalyst per pint of Prime Time. Mix thoroughly. Do not shake.

Not applicable. No catalyst required.

Mix 3103 catalyst with Prime Time 2% by weight. (weight of piant) x .02= weight of catalyst For example, if you are using 100 grams of Prime Time, add 2 grams of 3103 catalyst. If no scale is available, then mix 2 teaspoons of catalyst per pint of Prime Time. Mix thoroughly. Do not shake.

If using 3103 catalyst, then mix 2% by weight to Black Cat or 2 grams of catalyst for every 100 grams of Black Cat. If no scale is available, then mix 2 teaspoons of catalyst per pint of Black Cat. Mix thoroughly. Do not shake.

Base coat gun with a 1.0 mm to 1.4 mm nozzle.

Base coat gun with a 0.8 mm to 1.3 mm nozzle.

Base coat gun with a 1.0 mm to 1.4 mm nozzle.

Base coat gun with a 1.2 mm to 1.4 mm nozzle for smooth finish. Primer gun with a 1.8 mm to 2.0 mm nozzle for high build.

Apply one light coat. Immediately apply second light coat if needed to hide thin areas. If second full coat is desired, allow Prime Time to flash off before applying second full coat. Flash time varies depending on temperature and humidity. Flash time is usually between 10 and 30 minutes.

Apply one light coat. Immediately apply second light coat if needed to hide thin areas. If second full coat is desired, allow Bumper and Cladding Coat to flash off before applying second full coat. Flash time varies depending on temperature and humidity. Flash time is usually between 5 and 10 minutes.

Apply one light coat. Immediately apply second light coat if needed to hide thin areas. If second full coat is desired, allow Prime Time to flash off before applying second full coat. Flash time varies depending on temperature and humidity. Flash time is usually between 10 and 30 minutes.

Apply one medium coat. If second coat is desired, allow Black Cat to flash off before applying second full coat. Flash time varies depending on temperature and humidity. Flash time is usually between 10 and 30 minutes. Additional coats may be applied after sanding to achieve desired surface finish if needed.

Allow at least 60 minutes dry time at room temperature or 30 minutes at 120°F. Dry time will vary depending on temperature and humidity. Prime Time must be completely dry before topcoating. The crosslinking process takes six hours at room temperature or one hour at 120°F. Prime Time may be topcoated before crosslinking is complete.

Allow at least 60 minutes dry time at room temperature or 15 minutes at 130°F. Dry time will vary depending on temperature and humidity. Bumper and Cladding Coat must be completely dry before topcoating. Any unused paint may be returned to the can for future use.

Allow at least 60 minutes dry time at room temperature or 30 minutes at 120°F. Dry time will vary depending on temperature and humidity. Prime Time must be completely dry before topcoating. The crosslinking process takes six hours at room temperature or one hour at 120°F. Prime Time may be topcoated before crosslinking is complete.

Allow at least 30 minutes dry time at room temperature or 15 minutes at 120°F before dry sanding. Black Cat may be wet sanded after 6 hours dry time at room temperature or after 60 minutes at 120°F. Dry time will vary depending on temperature and humidity. Black Cat must be completely dry before topcoating. The crosslinking process takes six hours at room temperature or one hour at 120°F. Black Cat may be topcoated before crosslinking is complete.

Continued on Page 16

OEM Primed Bumpers

RAW TPO Bumpers

RAW PUR Bumpers

OEM Painted Bumpers

REPAIR STEP

5

Priming Plastics: primer selection & use

800.633.3047

Page 15

Document info
Document views34
Page views34
Page last viewedSun Dec 04 22:04:33 UTC 2016
Pages16
Paragraphs651
Words8820

Comments