X hits on this document

PDF document

Kit Number 57-0562 Fiat Bravo 1.4L L4 F/I Exc. Turbo 07-09 Fiat Grande Punto 1.4L L4 16V F/I Exc. ... - page 1 / 4

24 views

0 shares

0 downloads

0 comments

1 / 4

Kit Number 57-0562 Fiat Bravo 1.4L L4 F/I Exc. Turbo 07-09 Fiat Grande Punto 1.4L L4 16V F/I Exc. Turbo

Fiat Grande Punto 1.4L L4 F/I 95BHP 2009 Instruction sheet A2054-755

  • 1.

    Take the key from the ignition and disconnect the negative terminal from the vehicle battery.

  • 2.

    Unclip and remove the intake hose from between the air box and throttle body. (Fig. 1)

  • 3.

    Unscrew and remove the air box from the vehicle. (Fig 2)

  • 4.

    Assemble the saddle bracket to the mounting bracket using the countersunk screw, conical washer, flat metal washer and nylock nut supplied. (Fig. 3)

  • 5.

    Fit the mounting bracket to the vehicle using the supplied bolt as shown. Don’t fully tighten yet! (Fig. 4)

  • 6.

    Fit the aluminium filter adapter into the original intake hose as shown and fully tighten the supplied hose clamp. (Fig. 5)

  • 7.

    Re-install the intake tube onto the throttle body, using the original hose clamp. (Fig. 6)

  • 8.

    Fit the hose clamp supplied around the saddle bracket.

  • 9.

    Fit the filter around the metal tube, through the saddle bracket and tighten the hose clamp as shown. (Fig. 7)

  • 10.

    Adjust the filter charger assembly for clearance and tighten all connections.

  • 11.

    Carefully expand the flexi cold air hose assembly. Feed the hose down to the under tray.

  • 12.

    Secure the flexi cold air hose to the cable harness using a cable tie supplied. (Fig. 8)

  • 13.

    Secure the flexi cold air hose to the under tray/bumper spoiler using the plastic cable ties supplied; ensure the hose points forward. (Fig. 9)

  • 14.

    Carry out a final height/alignment check of the K&N induction system and double-check all connections before starting the engine. Installation is now complete.

Fig. # 1

Fig. # 2

Fig. # 3

Fig. # 4

Fig. # 5

Fig. # 6

Fig. # 7

Fig. # 8

Fig. # 9

WWW.KNFILTERS.COM

Parts list: 1 x Filter Element. 1 x Literature Pack. 1 x Flexi Cold Air Hose. Fixing Kit : 1 x ‘L’ Bracket. 1 x Saddle Bracket. 2 x Flat Metal Washer. 1 x M6 Nylock Nut. 1 x C’sunk Bolt. 1 x Conical Nylon Washer. 1 x M6 Hex Head Bolt. 1 x Adaptor Tube. 1 x Hose Clamp 2 x Plastic Tie.

WARNING: Before starting the engine carry out a final fitment check of the K&N performance air box. It will be necessary to check the air box periodically for realignment, clearance and tightening of all connections. Failure to follow the above instructions or proper maintenance may void the warranty.

FILTER MAINTENANCE: K&N suggests checking the filter periodically for excessive dirt build- up. When the element becomes covered in dirt (or once a year), service it according to the instructions on the Recharger service kit available from your K&N dealer, part number 99-5003EU

For the cleaning instructions please visit our website: www.knfilters.com/cleaning

                  

               

Document info
Document views24
Page views24
Page last viewedFri Jan 20 12:13:07 UTC 2017
Pages4
Paragraphs141
Words1760

Comments