X hits on this document

70 views

0 shares

0 downloads

0 comments

15 / 35

Fiber Testing, Troubleshooting and Certification

28

Fiber Inspection and Cleaning

FI-7000 FiberInspectorPro

End-face contamination is a leading cause of fiber failures. Dirt and contaminant cause insertion loss and back-reflection that inhibits optical transmission and causes havoc with transceivers. Fiber loss and OTDR testing can expose this problem, but in many cases, dirty connections make fiber testing time consuming and inaccurate.

Since dirt can be an issue before, during, or after fiber optic certification testing, and migrate from one end-face to another upon mating, both sides of any connection must always be cleaned and inspected. Further, mating contaminated connectors can cause permanent damage as microscopic debris is crushed between end-faces in physical contact. Even factory terminated patch cords or pigtails must be in- spected as protective caps do not keep end-faces clean. Avoiding this common cause of failure, starts with inspecting the end-face and eliminating any contamination before insertion into a bulkhead or piece of equipment.

The FI-7000 FiberInspector Pro allows you to inspect and certify end-faces in 2 seconds so you can get the job done the first time. Automated PASS/FAIL certification take the guess work out of fiber inspection so anyone can be a fiber expert.

  • Automated Pass/Fail certification of fiber end-faces

  • Graphical indication of problem areas due to contamination, pits, chips, and scratches

  • Certify to industry standards—IEC 61300-3-35

  • Eliminate human subjectivity from end-face measurements

Description FiberInspector Pro FiberInspector Pro w/MFO and cleaning

Gold 1YR GLD-FI-7000 GLD-FI-7000-MPO

Gold 3YR GLD3-FI-7000 GLD3-FI-7000-MPO

FI-1000 USB Fiber Inspection Video Probe with selective bulkhead and video probe tips.

GLD-FI

FI-1000 FiberInspector USB video probe for Versiv platform.

GLD-FI

Model FI-7000 FI-7000-MPO

FI-1000-KIT

FI-1000

Accessories

Model FI1000-SCFC-TIP FI1000-LC-TIP FI1000-ST-TIP FI1000-MU-TIP FI1000-E2KAPC-TIP FI1000-SCAPC-TIP FI1000-E2K-TIP FI1000-LCAPC-TIP FI1000-2.5-UTIP FI1000-1.25-UTIP FI1000-2.5APC-UTIP FI1000-MPO-UTIP FI1000-MPOAPC-UTIP FI1000-1.25APC-TIP FI1000-MPOAPC-RT FI1000-MPO-RT

Description SC and FC bulkhead video probe tip LC bulkhead video probe tip ST bulkhead video probe tip MU bulkhead video probe tip E2000/APC bulkhead video probe tip SC/APC bulkhead video probe tip E2000 bulkhead video probe tip LC/APC bulkhead video probe tip

    • 2.5

      mm universal video probe tip for patch cords

    • 1.25

      mm universal video probe tip for patch cords

    • 2.5

      mm APC universal video probe tip for patch cord

MPO probe tip and translator knob for patch cords and bulkheads MPO/APC probe tip and translator knob for patch cords and bulkheads 1.25 mm APC universal video probe tip for patch cords MPO/MTP APC replacement tip with no translator knob MPO/MTP replacement tip with no translator knob

www.flukenetworks.com/fiberinspection

FiberInspectorMini Video Microscope

The FiberInspector Mini video microscope enables The portable video microscope projects a crisp, clear image of microscopic debris and end-face damage.

  • The exceptionally convenient FiberInspector Mini uses a 200x magnification probe sufficient for inspecting both multimode and singlemode fiber

  • Quickly determines whether fiber connectors on a

Model

Description

FT500

FiberInspector Mini Video Microscope

FT525

FiberInspector Mini and Cleaning Kit

Gold 1YR

GLD-FTINSPECTOR

GLD-FTINSPECTOR

hardware device are clean and in good condition without disassembling the device

Accesorries

Model NFM110 NF390 NFM120

Description Accessory tip set for FiberInspector Mini APC (Angled Physical Connector) video adapter probe for FiberInspector Mini Rechargeable battery for FiberInspector Mini (NIMH) for FiberInspector Mini

To learn more visit: www.flukenetworks.com/fiberinspectormini

FiberViewerFiber Microscope

The FiberViewer fiber microscope ensures a termina- tion is clean and ready for optical transmission. FT120 offers 200X magnification, FT140 offers 400X magnification

Model FT120 FT140 NF350

Description FiberViewer, 200X FiberViewer, 400X 1.25 mm universal microscope adapter

To learn more visit: www.flukenetworks.com/ fiberviewer

Model

Description

VisiFault

VisiFault Visual Fault Locator with 2.5 mm universal adapter

NF380

1.25 mm Universal VisiFault Adpater

VisiFaultVisual Fault Locator

The laser-powered VisiFaultVisual Fault Locator (VFL) traces fibers, verifies continuity and polarity, and helps find breaks in cables, connectors and splices. Continuous and flashing modes for easier identifica- tion. Compatible with 2.5 mm and 1.25 mm connectors for easy connection.

  • Bright red visible laser light source, features continuous and flashing modes

  • Accelerates end-to-end fiber continuity checks

  • Speeds fiber tracing and identification

  • Aids in location of fiber faults including tight bends, breaks and bad connectors

To learn more visit: www.flukenetworks.com/visifault

1-800-283-5853 (US and Canada) • www.flukenetworks.com

Fiber Testing, Troubleshooting and Certification

29

Document info
Document views70
Page views70
Page last viewedSun Nov 27 22:42:04 UTC 2016
Pages35
Paragraphs2776
Words20939

Comments