for Manufacturer (FSCM) in parentheses. The FSCM is used as an element in item identification to designate manufacturer or distributor or Gov- ernment agency, etc., and is identified in SB 708-42.
b. T h e f o l l o w i n g p u b l i c a t i o n p e r t a i n s t o t h e e q u i p -
ment and its components: TM 11-6625-316-12 Operator
d. Unit of Measure (U/M). I n d i c a t e s t h e s t a n d a r d or basic quantity by which the listed item is used in performing the actual maintenance function. This
Sets, Electron Tube TV-2A/U, TV-2B/U, 2C/U.
TV-2/U, and TV-
measure is expressed by betical abbreviation; e.g., ea,
two-character in, pr, etc., and
alpha- is the
1-5. Location of Repair Parts
basis used to indicate subsequent columns. differs from the unit issue that will satisfy will be requisitioned.
quantities and allowances in When the unit of measure of issue, the lowest unit of the required units of measure
e. Quantity Incorporated in a Unit. This column indicates the quantity of the item used in the equip- ment. Subsequent appearances of the same item in the same assembly are indicated by the letters “REF”.
15-Day Organizational Maintenance Allowance.
The repair parts indicated by an asterisk
in the allowance column represent those authorized for use at the organizational category, and will be
a. T h i s m a n u a l c o n t a i n s o n e c r o s s - r e f e r e n c e i n d e x (sec V) to be used to locate a repair part when either the Federal stock number or reference num- ber (manufacturer’s part number) is known. The first column in the index is prepared in numerical or alphanumeric sequence in ascending order. The reference numbers (manufacturer’s part numbers) are listed immediately following the last listed Fed- eral stock number in the index of Federal stock numbers.
b. W h e n number is
the Federal stock number or reference known, follow the procedures given in
requisitioned on age is based on
an “ a s r e q u i r e d ” b a s i s , u n t i l s t o c k - demand in accordance with AR
to approve reduction in the range of support items authorized for use in units within their commands. Recommendations for increase in range of items authorized for use will be forwarded to Commander, US Army Electronics Command, ATTN: AMSEL-
(1) Refer to the index of Federal stock num- bers (sec V) and locate the Federal stock number or reference number. The FSN and reference number
cross-referenced to the applicable number or reference designation.
(2) Refer to the repair parts list (sec III)
locate the figure number (col 7a) and item number
r r e f e r e n c e d e s i g n a t i o n (C Ol 7b) as noted in the
approved RPSTL. (3)
are indicated in the
special tools list section and other equipment.
for special tools, TMDE,
c. W h e n t h e f i g u r e a n d i t e m n u m b e r o r r e f e r e n c e designation are known, scrutinize columns 7a and 7b of the repair parts list (sec III) until the item is located.
g. Illustration. T h i s c o l u m n i s d i v i d e d a s f o l l o w s :
(1) Figure number. of the illustration on 11-6625-316-12.
Indicates which the
is shown in
d. W h e n t h e F S N , r e f e r e n c e n u m b e r , f i g u r e n u m - ber, item number and reference designation are not known, scrutinize column 3 of the repair parts list (sec III), which is arranged in alphabetical order.
(2) Item number. Indicates the item number or reference designation used to reference the item in the illustration.
1-6. Abbreviations Not applicable.
1-4. Special Information
a. U s a b l e o n c o d e s a r e i n c l u d e d i n c o l u m n 3 . U n - coded items are applicable to all models. Identifica- tion of the usable on codes used in this publication are-
Reporting of Equipment Publication Improvements
The reporting of errors, omissions, and recommen- dations for improving this publication by the in- dividual user is encouraged. Reports should be sub- mitted on DA Form 2028 (Recommended Changes to Publications) and forwarded direct to Com-
AMSEL-MA-CRA, Fort Monmouth, NJ 07703.
(Next printed page is 6)