X hits on this document

11 views

0 shares

0 downloads

0 comments

2 / 5

2REYNOBOND PE COLORWELD 500OCTOBER, 2014 Guide Specs074213 FORMED METAL WALL PANELSEC 97909-055

A.

American Society for Testing and Materials (ASTM)

1.

ASTM E330: Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.

2.

ASTM E283: Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.

3.

ASTM D1781: Standard Test Method for Climbing Drum Peel Test for Adhesives.

4.

ASTM E84: Standard Test Method for Surface-Burning Characteristics of Building Materials.

5.

ASTM E283: Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.

6.

ASTM D3363: Standard Test Method for Film Hardness by Pencil Test.

7.

ASTM D2794: Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact).

8.

ASTM D3359: Standard Test Methods for Measuring Adhesion by Tape Test.

9.

ASTM D2247: Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity.

10.

ASTM B117: Standard Practice for Operating Salt Spray (Fog) Apparatus.

11.

ASTM D822: Standard Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings.

12.

ASTM D1308: Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes.

13.

ASTM D1735: Standard Practice for Testing Water Resistance of Coatings Using Water Fog Apparatus.

14.

ASTM D1929: Standard Test Method for Determining Ignition Temperature of Plastics.

15.

ASTM D635: Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in Horizontal Position.

B.

American Architectural Manufacturers Association

1.

AAMA 2605 Superior Performance of Organic Coating on Aluminum

1.4

Submittals

A.

Submittals shall be in conformance with section_________________.

B.

Samples

1.

Panel assembly: Two samples of each type of assembly, 304 mm (12”) x 304 mm (12”) minimum.

2.

Two samples of each color or finish selected, 76 mm (3") x 102 mm (4") minimum.

3.

Custom-color samples will contain drawdown lines. Sizes for custom-color samples are limited.

C.

Shop Drawings: Submit shop drawings showing project layout and elevations; fastening and anchoring methods; detail and location of joints, sealants and gaskets, including joints necessary to accommodate thermal movement; trim; flashing; and accessories.

D.

Manufacturer’s literature shall certify that material meets specifications.

E.

Fabrication Tickets: Submit fabrication drawings showing location and type of aluminum-extruded stiffeners at typical panels and at corner panels, if required.

F.

Documents showing product compliance with the local building code shall be submitted prior to the bid. These documents may include evaluation reports, test reports, supporting document and drawings, and manufacturer’s data. The architect must approve alternate material prior to bid date.

1.5

Warranty

A.

The fabricator and installer will warrant the wall system for a period of 1 year that the fabrication and installation workmanship will be free from defects.

B.

The aluminum composite material manufacturer shall warrant for a period of 30 years against Max 5 fade based on ASTM D2244 and Max 8 chalk based on ASTM D4212 and delamination of the paint finish.

1.6

Packaging, Shipping and Handling

A.

Follow manufacturer's recommendations.

B.

Store material in accordance with panel manufacturer's recommendations.

PART 2 -

Products

SPCI017 reynobond.com

Document info
Document views11
Page views11
Page last viewedTue Dec 06 14:34:18 UTC 2016
Pages5
Paragraphs320
Words3051

Comments